Unboxing a new figure: what to check
A few calm minutes at unboxing protect your figure, your return rights and its resale value. Here is how to open, assemble and check a new figure.
· 4 min read

A new figure is exciting, and it is tempting to tear the box open. Take a few minutes instead. Most damage to new figures happens in the first hour, not in the mail. A careful unboxing also keeps your options open if something is wrong, and keeps the box in good shape if you ever sell the figure.
Before you open the box
Look at the shipping carton first. If it is dented, crushed, wet or torn, take photos before you open it. Photograph every side and any label. Then open the carton and photograph the figure box the same way before you go further.
If the parcel arrived on a cold day, wait. Leave the figure in its box for a few hours until it reaches room temperature. Cold PVC is stiffer and more brittle, so thin parts snap more easily. Opening a cold box in a warm room can also cause condensation on the figure.
Open carefully
Clear a table and put down a soft cloth or towel. Small parts roll, and a soft surface stops them from bouncing onto the floor.
- Cut tape with a small blade held flat, and only cut the tape, not the box
- Open the box flaps slowly, since some boxes have tabs that tear
- Slide the inner tray out. Don't pull it by the figure
- Work over the cloth, never over a hard floor
Keep the box and all plastic
Keep the box, the blister trays, the plastic bags, the twist ties and the instruction sheet. You need the original packaging to return a figure. Collectors also pay more for a figure with a complete, clean box. Flatten nothing and throw nothing away until you are sure you are keeping the figure. Even then, store the packaging somewhere dry.
Removing the blister trays
Most figures sit in clear plastic trays, called blisters. They hold each part tightly so nothing moves in transit. That grip also means parts can catch on the way out.
- Remove any tape that holds the two halves of the blister together
- Open the blister gently, like a book, instead of pulling it apart
- Lift each part out by its thickest area, such as the body or the base
- Never pull a figure out by a sword, a hair tip, a hand or a ribbon
- Take off small plastic sleeves and paper wraps last, with care, since they protect paint
Attaching parts and the base peg
Read the instruction sheet, even if it is not in your language. The pictures show which part goes where. Lay all parts out on the cloth before you start.
Most figures stand on a base with 1 or 2 metal or plastic pegs. The pegs go into holes in the feet. Hold the figure by the legs or the body, line the hole up with the peg, and press straight down. Do not twist hard or push at an angle. For other parts, test the fit first, then press gently until it seats.
If a peg is too tight
Tight pegs are common on new figures. Forcing them is how ankles crack. A hair dryer on low heat can help, but only on PVC figures.
- Set the hair dryer to low heat, not high
- Hold it about 15 cm away and keep it moving
- Warm the foot or the joint for 10 to 20 seconds, then try again
- Stop if the area feels hot to the touch
- Never use heat on resin or polystone, including GK statues, since it can damage the paint and the material
If a peg still will not go in after a couple of tries, stop. Write to the seller before you force anything.
If a part does not fit, warm it or stop. Never force it.
Check the figure against the product photos
Once the figure is standing, open the product page and compare. Check it in good light from all sides.
- All parts and extras listed on the page or the box are there
- Paint is clean on the face, eyes and skin
- No cracks, chips, scuffs or loose parts
- Nothing is bent, such as weapons, hair or thin accessories
- The figure stands straight on its base without leaning
Small factory marks, like a faint seam line, are normal on mass-produced figures. Cracks, broken parts, missing pieces or clear paint damage are not.
If something is damaged or missing
Stop unpacking further and take photos of the damage, the box and the packaging as it arrived. Keep everything. Then write to us at [email protected], or use the contact form, with your order number and the photos. If the figure arrived damaged or wrong, we replace it or refund you in full, and return shipping is included.
If the figure is fine but you change your mind, you can return it within 14 days of delivery. Write to us with your order number, and send it back unused in its original packaging. We refund the price and the standard shipping within 14 days of your return notice. In that case the return postage is yours to pay. This is one more reason to keep every piece of the packaging.
GachaBay team
Figure specialists
We are a small shop that only sells anime figures. We write these guides from the questions collectors send us most.



