Caring for your figures: PVC and resin
Simple habits that keep PVC and resin figures clean, upright and bright for years, plus what never to put on the paint.
· 5 min read

Most figures do not need much care. They need the right care. Dust, sunlight, heat and careless handling cause nearly all the damage collectors see. This guide covers PVC figures, the material of most scale and prize figures, and resin statues such as GK pieces, which need a gentler touch.
Dusting the right way
Dust a little and often. Fresh dust comes off easily. Old dust mixes with grease from the air and gets harder to move.
- Use a soft brush, such as a clean makeup brush or a wide paintbrush. Work from the top down.
- Use a hand air blower for gaps in hair, clothing folds and lace.
- If you use canned air, hold the can upright and keep it at a distance. A tilted can may spray cold propellant that marks the paint.
- Skip feather dusters and rough cloths. They catch on small parts.
A closed display case cuts dusting down a lot. It is the single best thing you can do for your figures.
Never use solvents
Alcohol, acetone, nail polish remover, paint thinner and household cleaners can soften or strip paint in seconds. They can also turn glossy parts cloudy. Do not use them on any figure, not even on a hidden spot.
Washing PVC figures
When a PVC figure is grimy, a gentle wash helps. Use this for PVC only, never for painted resin.
- Take the figure off its base and remove any parts that come off easily.
- Fill a bowl with lukewarm water and a drop of mild dish soap. Never use hot water, as heat can warp PVC.
- Clean gently with a soft brush. Do not scrub painted lines or printed eyes.
- Rinse in clean lukewarm water.
- Let it air dry fully on a towel before you put it back together.
Sunlight, heat and humidity
Sunlight is the main enemy. UV light fades paint and turns white and pale parts yellow over time. That damage cannot be undone. Keep figures out of direct sun, and keep the boxes out of it too.
Heat causes leaning. PVC softens a little when it is warm, and a figure that stands on 1 foot or leans forward can slowly tilt over months. Keep figures away from radiators, heaters, sunny windowsills and hot cars. Warm display lights can do the same, so choose LED lights that stay cool.
Humidity matters as well. Damp rooms can lead to mold on boxes and tarnish on metal parts. Very dry, hot air is hard on paint. A normal living room climate is fine. Avoid attics, basements and garages.
Sticky PVC
Some older PVC figures turn sticky. This happens when softeners in the plastic move to the surface, and heat speeds it up. A gentle wash with mild soapy water, as above, usually removes the film. Dry the figure well and move it to a cooler spot. The film can come back over time, so check it now and then.
Handling, pegs and ankles
Most breaks happen in your hands, not on the shelf.
- Hold the figure by the base or the solid middle of the body. Never by hair tips, weapons, fingers or effect parts.
- Handle it with clean, dry hands. Cotton gloves help with glossy or pale paint.
- Push pegs into the base straight down. Do not twist or force them.
- If a peg is too tight, warm the peg hole briefly with a hair dryer on a low setting, then try again.
- Thin ankles carry the whole weight. If a figure starts to lean, give it support or lay it down for a while. Do not bend it back by force.
Storing figures in the box
Keep the box. It protects the figure for moves and storage, and it matters for resale and for returns. Store boxes upright in a dry, dark and cool place. Keep the plastic tray and inner wrap, and pack the figure the way it arrived. Do not stack heavy boxes on top of a figure box, since a crushed tray can bend thin parts.
Fixing a loose part safely
Many parts come off by design. Check for pegs or magnets first, and read the instruction sheet.
If a part is truly broken, use a small amount of glue made for plastic and test it somewhere hidden. Super glue can leave a white haze on glossy paint, so apply very little with a toothpick. For heavy resin parts, a 2-part epoxy holds better than super glue.
If a figure arrives broken or with a loose part, do not glue it. Photograph the damage before you unpack further, then send the photos with your order number to [email protected]. We replace it or refund in full, return shipping included.
Resin specifics
Resin statues, including GK pieces, are heavier and more brittle than PVC. They do not bend. A drop or a knock usually means a clean break.
- Dust only. Do not wash painted resin with water.
- Lift it with 2 hands under the base, never by a sculpted part.
- Place it on a stable, level surface that can take the weight, away from edges.
- Resin does not lean like warm PVC, but sunlight still fades its paint.
- Keep the original foam packing for any move.
Keep it out of the sun, away from heat, and dust it gently. That covers most of figure care.
GachaBay team
Figure specialists
We are a small shop that only sells anime figures. We write these guides from the questions collectors send us most.



